When searching for a filter or vessel by part number enter the first series of letters to find the webpage you are looking for.

PP-Series Overview

The pleated depth media is encapsulated in an integral, continuous-length, thermally-bonded structure for cleanliness, pressure tolerance, and chemical inertness. Offered in both absolute-rated (up to 99.98% retention) and nominally-rated (90% retention) grades in all end configurations. Manufactured in a clean-room environment to maintain high standards of purity and cleanliness. Commonly used in food/beverage and chemical applications as a final filter or prefiltration stage.

Typical Applications

  • Food & Beverage
  • Deionized Water
  • R.O. Pre-Filtration
  • Process Water
  • Fine Chemicals
  • Plating Chemicals
  • Wastewater
  • Pharmaceutical Prefiltration

Construction Materials

  • Filtration Media: Polypropylene
  • Support Media: Polypropylene
  • End Caps: Polypropylene
  • Center Core: Polypropylene
  • Outer Support Cage: Polypropylene
  • O-Rings/Gaskets: Buna, EPDM, Silicone, Teflon® Encapsulated Viton®, Viton®, Teflon® Encapsulated Silicone

Operating Conditions

  • Change Out ΔP (recommended) 35 PSID
  • Temperature (max) 176˚F (80˚C)
  • Differential Pressure (max) 60 PSID (4.1 bar) at 68˚F (20˚C)
  • Note: Stainless steel insert option required for all cartridges being hot water sanitized or steam sterilized

Sanitization/Sterilization

  • Filtered Hot Water: 80 ̊C for 30 min.
  • Steam Sterilization: 121 ̊C for 30 min., multiple cycles
  • Chemicals: Cartridges are compatible with most chemical sanitizing agents.
  • Note: Stainless steel insert option required for all cartridges being hot water sanitized or steam sterilized.

Dimensions

  • Length: 10 to 40 inches ( 25.4 to 101.6 cm)
  • Outside Diameter: 2.70 inches

NSF Certificate

NSF Certification applies for use only with drinking water. Only products bearing the NSF Mark on the product, product packaging, and/or documentation shipped with the product are Certified. Product options denoted with an asterisk (*) are not included in the Certification.

Flow Rate vs Pressure Drop

Food Safety Compliance

Materials of construction comply with FDA regulations for food and beverage contact use as detailed in the US Code of Federal Regulations, 21CFR. Materials used to produce filter media and hardware are deemed safe for use in contact with foodstuffs in accordance with EU Directives 1935/2004, and/or 10/2011.

Toxicity

All polypropylene components meet the specifications for biological safety per USP Class VI – 121˚C for plastics.

PP-Series Ordering Specifications

Micron Ratings0.2, 0.45, 1.0, 2.0, 5.0, 10.0, 20.0, 40.0
RetentionN = Nominal, A = Absolute
Lengths10″, 20″, 30″, 40″
End Caps2 = DOE Flat Gasket
3 = 222 w/ Fin
4 = 222 w/ Flat Cap
5 = 222 w/ Spring
6 = 226 w/ Flat Cap
7 = 226 w/ Fin
8 = 226 w/ Spring
16 = 213 Internal O-Ring
28 = 222 3-Tabs w/ Fin
O-Rings/GasketsB = Buna
E = EPDM
S = Silicone
T = Teflon® Encapsulated Viton®*
V = Viton®*
Z = Teflon® Encapsulated Silicone*
AddersCS = 316SS Compression Spring
FG = Glass Reinforced PP Core*
HP = Heavy Poly Core*
I = Stainless Steel Insert
R = 18 Megaohm Rinse
SS = Stainless Steel Core